[Free] 2019(Nov) EnsurePass iSQI CTFL-001 Dumps with VCE and PDF 281-290

Get Full Version of the Exam
http://www.EnsurePass.com/CTFL-001.html

Question No.281

Which of the following are #39;Exit Criteria?#39;

  1. Acceptance criteria, completion criteria, pass/fail criteria.

  2. Coverage of code, schedule, estimates of defect density.

  3. The last executable statement within a component.

  4. Cost overruns.

Correct Answer: B

Question No.282

What is decision table testing?

  1. It#39;s a testing design technique based in the internal software structure.

  2. It#39;s a static test design technique.

  3. It#39;s a testing design technique to verify decisions.

  4. It#39;s a testing design technique based in the system requirements.

Correct Answer: D

Question No.283

Of the following, select the best description of the fundamental test process:

  1. Planning and control, analysis, design, implementation, execution, evaluation of exit criteria and reporting, test closure.

  2. Executing tests, identifying and recording defects and preparing recommendation and closure reports.

  3. Controls, preparation of test cases, execution of test cases, execution of regression packs, communicating with developers, writing recommendations for release.

  4. Static testing, dynamic testing, defect reporting, reporting and closure.

Correct Answer: A

Question No.284

Which of the following processes ensures that all items of testware are identified, version controlled, tracked for changes, so that traceability can be maintained throughout the test process?

  1. Software traceability process

  2. Incidence management process

  3. Testing design process

  4. Configuration management process

Correct Answer: D

Question No.285

What is the value of static code analysis?

  1. Detection of failures not easily found by other types of testing

  2. Early defect detection

  3. Detection of suspicious operations caused by deviations from regulations

  4. Detect deviations in standards by executing the source code

Correct Answer: B

Question No.286

Which of the following statements about use-case testing are most accurate?

  1. In a use-case diagram an actor represents a type of user.

  2. Use-cases are the most common test basis for unit testing.

  3. A use-case describes interactions between actors.

  4. An actor is always a human user that interacts with the system.

  5. Test cases can be based on use-case scenarios.

  6. Use-case testing will often identify gaps not found by testing individual components.

  1. ii, iii, iv, v

  2. i, iii, v, vi

  3. i, ii, iv, v

  4. iii, iv, v, vi

Correct Answer: B

Question No.287

It is recommended to perform exhaustive tests for covering all combinations of inputs and preconditions.

  1. Yes, it#39;s strongly recommended.

  2. No, risk analysis and priorities should be used to focus testing efforts

  3. Yes, and it#39;s also necessary to include all the exit combinations

  4. Only the expert testers can make exhaustive tests.

    Correct Answer: B

    Question No.288

    Refer to the exhibit.

    image

    Given the following State Transition diagram, match the test cases below with the relevant set of state transitions.

    1. X-Z-V-W

    2. W-Y-U-U

A. (i) = S1 – S2 – S3 – S4 – S2 and (ii) = S4 – S2 – S4 – S4 – S4

B. (i) = S1 – S2 – S3 – S4 – S4 and (ii) = S2 – S4 – S4 – S4 – S2

C. (i) = S2 – S3 – S4 – S2 – S2 and (ii) = S4 – S2 – S4 – S4 – S4

D. (i) = S2 – S3 – S4 – S4 – S2 and (ii) = S2 – S3 – S4 – S4 – S4

Correct Answer: A

Question No.289

A system calculates the amount of customs duty to be paid:

_ No duty is paid on goods value up to, and including, $2,000.

_ The next $8,000 is taxed at 10%.

_ The next $20,000 after that is taxed at 12%.

_ Any further amount after that is taxed at 17%.

To the nearest $, which of these groups of numbers fall into three DIFFERENT equivalence classes?

A.

$20,000 $20,001 $30,001

B.

$2,000 $2,001 $10,000

C.

$2,000 $8,000 $20,000

D.

$1,500 $2,000 $10,000

Correct Answer: C

Question No.290

What are metrics NOT used for?

  1. To identify the percentage of work done in test environment preparation.

  2. To identify the percentage of work done in test case preparation.

  3. To apply to the RAD development model.

  4. To measure whether dates of test milestones were met.

Correct Answer: C

Get Full Version of the Exam
CTFL-001 Dumps
CTFL-001 VCE and PDF

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.