[Free] 2019(Nov) EnsurePass IBM C9010-022 Dumps with VCE and PDF 31-40

Get Full Version of the Exam
http://www.EnsurePass.com/C9010-022.html

Question No.31

A DLPAR memory operation was attempted and failed. Given the following information, what is the likely caused?

image

  1. Source LPAR is using all of its allocated memory

  2. Operation timed out

  3. Destination LPAR maximum memory setting is too low.

  4. HMC RMC daemons are not communicating properly to the source

  5. Source LPAR minimum memory setting is too high.

  6. Source LPAR maximum memory setting is too low.

Correct Answer: C

Question No.32

A mirrored rootvg internal disk, hdisk1, has failed and must be replaced. The remaining mirrored disk, hdisk0,is intact and functioning normally. What is the correct sequence of actions?

  1. unmirrorvg rootvg hdisk1 reducevg roolvg hdisk1 rmdev -I hdisk1 -d physically replace hdisk1 cfgmgr

    extendvg rootvg hdisk1 mirroivg rootvg

    Run a bosboot on both disks

  2. rmdev-l hdisk1 -d physically replace hdisk1 cfgmgr

    unmirrorvg rootvg hdisk1 reducevg rootvg hdisk1 extendvg rootvg hdisk1 mirrorvg rootvg

    Run a bosboot on both disks

  3. unmirrorvg rootvg hdisk1 rmdev-I hdisk1 -d physically replace hdisk1 reducevg rootvg hdisk1 cfgmgr

    extendvg rootvg hdisk1 mirrorvg rootvg

    Run a bosboot on both disks

  4. unmirroivg rootvg hdisk1 reducevg rootvg hdisk1 rmdev -I hdisk1 -d physically replace hdisk1 cfgmgr

extendvg rootvg hdisk1

Run a bosboot on both disks mirrorvg rootvg

Correct Answer: A

Question No.33

Within a Perl script, how can the output of the hostname command be assigned to a variable called myHostname?

  1. chopfmyHostname-#39;hostname -s 2gt;/dev/nullquot;)

  2. chop($myHostname=%hostname -s 2gt;/dev/nuir);

  3. $myHostname=7usr/bin/hostnamequot;.

  4. chomp(@myHostname-hostname -s 2gt;/dev/null#39;);

Correct Answer: B

Question No.34

The cfgmgr command appears to be taking an excessive time to complete. The administrator was able toquit the command and return to the command prompt. The administrator does not have access to the managing HMC and unable to check for any LED codes. How else can the cause of the observed delay be determined?

  1. Review the latest entry within /var/log/cfgdb.out.

  2. Start the syslog daemon before re-issuing the command.

  3. Re-issue the command with the W flag.

  4. Initiate the ledmon command from a separate session, then re-issue cfgmgr.

Correct Answer: C

Question No.35

Two different administrators are asked to change the hostname of a system due to a misunderstanding The current hostname is set to misunderstanding. The current hostname is set to #39;ozi#39;. The first administrator thinks the hostname should be set to #39;kiwi#39; and he runs the command:

# hostname kiwi

He checks his work by running the hostname command again and he sees this output

# hostname kiwi

The second administrator thinks the hostname should be #39;texan#39; and he runs the command:

# uname -Stexan

He checks his work by running uname -n and sees the output

# uname -n texan

What will be the output of the hostname and uname -n command when the system reboots?

  1. The output of both commands will be #39;kiwi#39; after reboot.

  2. The output of both commands will be #39;texan#39; after reboot.

  3. The output of both commands will be #39;ozi#39; after reboot.

  4. The output of the hostname command will be #39;kiwi#39; and the output of the uname -n command will be texanquot;.

Correct Answer: C

Question No.36

After performing a NIM rte install, the administrator noticed that not all filesets are at the correct Technology Level (TL). What action will help the administrator determine why the inconsistent fileset levels were installed?

  1. On the NIM server, run an Ippchk to identify if the Software Vital Product Data is valid.

  2. On the NIM client, run oslevel command against the TL to identifymissing prerequisites.

  3. Run instfix command on NIM client to determine what filesets are inconsistent.

  4. On the NIM server run the NIM IsIpp command to indentify downlevel filesets contained in the lpp_source.

Correct Answer: D

Question No.37

The following information has been reported in an AIX error log:

image

How can the administrator prevent the error from reoccurring?

  1. Create a secondary dump device greater than 266MB

  2. Increase primary dump device size greater than 266MB

  3. Increase quot;/varquot; file system to ensure it has a minimum of 266MB free space

  4. Increase quot;/var/adm/ras/livedumpquot; file system to ensure it has a minimum of 266MB free space

Correct Answer: C

Question No.38

What TWO situations require a Systems Director Management Console (SDMC) instead of a Hardware Management Console (HMC)? (Select two)

  1. Managing POWER5, POWER6 and POWER7 servers from one interface.

  2. Creating automation plans that perform specific functions on a given event.

  3. Implementing Active Memory Sharing (AMS).

  4. Utilizing Integrated Virtualization Manager (IVM) to manage Power Systems blades.

  5. Managing Power Blades and Power Systems standalone servers from one interface.

Correct Answer: BE

Question No.39

What option will boot an LPAR directly from DVD media, without any user interaction required, when starting the LPAR from the Hardware Management Console (HMC)?

  1. Normal

  2. Diagnostic with default boot list

  3. System management services

  4. Open firmware OK prompt

Correct Answer: B

Question No.40

A P0WER5 520 system is being cloned onto a Power 780. The source system is on internal disks, and the vg01 volume group is mirrored. After installing AIX, which sequence of actions will recreate the vg01 volume group and restore data on the new system?

  1. Have all the applications shut down. Create a backup of each filesystem to an NFS mount using the backup command. Restore thefilesystem backups with the restorevgfiles command.

  2. Create a backup onto an NFS server using the mksysb command and referencing the correct data volume group Restore the backup of vg01 with the smit fast path smit restmksysb.

  3. Have all applications shut down. Use the savevg command to create a backup of the data volume group to an NFS mount. Restore the savevg on the clone system with the restvg command.

  4. Shut down all application running from the data volume group. Run the cpio command to write thefile to a local NFS server. Restore command with the backup to recreate vg01.

Correct Answer: C

Get Full Version of the Exam
C9010-022 Dumps
C9010-022 VCE and PDF