[Free] 2019(Nov) EnsurePass Cisco 640-692 Dumps with VCE and PDF 11-20

Get Full Version of the Exam
http://www.EnsurePass.com/640-692.html

Question No.11

What is the default operating mode you are initially logging into a router?

  1. global configuration

  2. privileged EXEC

  3. ROM monitor

  4. user EXEC

Correct Answer: D

Question No.12

What one of the feature is associated with single-mode fiber-optic cable?

  1. a single strand of glass fiber

  2. stored less bandwidth

  3. cost is less than multimode fiber

  4. operates over less distance than multimode fiber

Correct Answer: A

Question No.13

Which two of the following are component of WAN connection? (Choose two)

  1. router

  2. switch

  3. CSU/DSU

  4. Hub

  5. Bridge

Correct Answer: AC

Question No.14

When using a modem to provide out-of-band access to a Cisco router, which cable type is used to connect the wall jack to the modem?

  1. DB-25 to RJ-11

  2. RJ-11 to Rj-11

  3. RJ-45 to RJ-45

  4. RJ-11 to RJ-45

  5. RJ-11 to DB-9

Correct Answer: B

Question No.15

Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? (Choose two.)

image

  1. Router1 has specific boot system commands that instruct it to load IOS from a TFTP server.

  2. Router1 is acting as a TFTP server for other routers.

  3. Router1 cannot locate a valid IOS image in flash memory.

  4. Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

  5. Cisco routers will first attempt to load an image from TFTP for management purposes.

    Correct Answer: AC

    Question No.16

    Which statement about unique local IP addresses is true?

    1. Summarization is not supported.

    2. They require all prefixes to be unique.

    3. Their global IDs are assigned sequentially.

    4. They are routable to the public Internet.

Correct Answer: B

Question No.17

Refer to the exhibit. What does the CD LED indicate on the voice WAN interface card?

image

  1. An alarm condition

  2. Receive signal strength

  3. A carrier has been detected

  4. The interface is in loopback mode

Correct Answer: C

Question No.18

Which sequence begins a unique local IP address in binary notation?

A.

1111110

B.

1111111

C.

00000000

D.

1111100

Correct Answer: A

Question No.19

Which two commands are used to set the configuration register value? (Choose two)

  1. Router(config)#config-register 0x2102

  2. Router(config)#confreg 0x2102

  3. rommongt;config-register 0x2102

  4. rommongt;confreg 0x2102

  5. Router(config)#configuration-register 0x2102

Correct Answer: AD

Question No.20

The pins and RJ-45 are numbered from 1 through 8. With the material points of the plug facing

toward you, pin 1 is the leftmost pin. Which two sets are looped on an RJ-45 T1 loopback plug? (Choose two)

  1. Pins 1 and 4

  2. Pins 1 and 7

  3. Pins 2 and 5

  4. Pins 2 and 8

  5. Pins 1 and 5

  6. Pins 2 and 7

Correct Answer: AC

>

Get Full Version of the Exam
640-692 Dumps
640-692 VCE and PDF

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.