[Free] 2019(Nov) EnsurePass Cisco 300-165 Dumps with VCE and PDF 51-60

Get Full Version of the Exam
http://www.EnsurePass.com/300-165.html

Question No.51

Which command sequence correctly enables Adapter FEX on Nexus 5000 Series Switches?

  1. switch(config)# install feature-set virtualization switch(config)# feature-set virtualization

  2. switch(config)# install feature-set adapter-fex switch(config)# feature-set adapter-fex

  3. switch(config)# install feature-set adapter-fex switch(config)# feature-set virtualization

  4. switch(config)# install feature-set virtualization switch(config)# feature-set adapter-fex

Correct Answer: A

Explanation:

install feature-set virtualization : installs the cisco virtual machine feature set on the switch. feature-set virtualization : enables the cisco virtual machine feature on the switch.

Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/adapter- fex/513_n1_1/b_Configuring_Cisco_Nexus_5000_Series_Adapter- FEX_rel_5_1_3_N1/b_Configuring_Cisco_Nexus_5000_Series_Adapter- FEX_rel_5_1_3_N1_chapter_010.pdf

Question No.52

DRAG DROP

Drag the security description on the left to the appropriate security feature on the right.

image

Correct Answer:

image

Question No.53

Which two statements about implementing Cisco NPV and NPIV on a Cisco Nexus 5000 Series switch are true? (Choose two.)

  1. STP must run inside the FP network.

  2. All VLANs must be in the same mode, CE, or FP.

  3. FP port can join the private and nonprivate VLANs.

  4. Only F and M series modules can run FabricPath.

  5. These require an enhanced Layer 2 license to run.

Correct Answer: BE

Explanation:

With the Nexus 5×00 switch, FCoE functionality is a licensed feature. After the license is installed, FCoE configuration can be completed.

Reference: http://www.ciscopress.com/articles/article.asp?p=2030048amp;seqNum=4

Question No.54

Which two items are features that are available in VN-Link in software? (Choose two.)

  1. VM snapshot

  2. NetFlow

  3. ERSPAN

  4. high availability

  5. resource reservations

Correct Answer: BC

Explanation:

NetFlow is a feature that was introduced on Cisco routers that provides the ability to collect IP network traffic as it enters or exits an interface. By analyzing the data provided by NetFlow, a network administrator can determine things such as the source and destination of traffic, class of service, and the causes of congestion. A typical flow monitoring setup (using NetFlow) consists of three main components:

Flow exporter: aggregates packets into flows and exports flow records towards one or more flow collectors.

Flow collector: responsible for reception, storage and pre-processing of flow data received from a flow exporter.

Analysis application: analyzes received flow data in the context of intrusion detection or traffic profiling,

This module describes how to configure Encapsulated Remote Switched Port Analyzer

(ERSPAN). The Cisco ERSPAN feature allows you to monitor traffic on one or more ports or VLANs and send the monitored traffic to one or more destination ports.

Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/lanswitch/configuration/xe- 3s/lanswitch-xe-3s-book/lnsw-conf-erspan.html

Question No.55

Which three selections represent implementations of Cisco VN-Link technology? (Choose three.)

  1. Cisco Nexus 1000V

  2. Cisco Nexus 2000 FEX

  3. Cisco VM-FEX

  4. VMware PTS

  5. vMotion

Correct Answer: ACD

Explanation:

The VM is powered on and resides on the ESX Host 1 with all the information stored on the shared storage.

The VM was connected to the PODy (where y is the number of your POD) PTS VDS by associating it to port group VLAN61 that was created on the Cisco Nexus 5548 device. The VM has been connected to the vPC system automatically using a VN-Link in the hardware in PTS mode or in VM-FEX mode.

The VEM bits are used in PTS mode to connect the VM VNIC to the VMNIC interface.

In this case, the VMNIC interface is not a real VMNIC but a dynamic VNIC that is presented as an interface to the ESX OS. The dynamic VNIC is enabled when the Cisco UCS VIC creates and configures the VNIC parameters inherited from port group VLAN61.

Reference: http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/mkt_ops_guides/513_n1_1/ n5k_ops_vmfex.html

Question No.56

When connecting Cisco Nexus 5000 Series Switches to the VMware vCenter Server, which item must be configured before installing the extension keys?

  1. configure vPC

  2. configure DirectPath I/O support in vCenter

  3. configure PTS on the VSM

  4. configure dynamic vNICs

Correct Answer: A

Question No.57

Which three VDC resources can be constrained with a resource template? (Choose three.)

  1. ACLs

  2. NAT entries

  3. IPv4 routes

  4. IPv6 routes

  5. SPAN sessions

  6. RBAC users

Correct Answer: CDE

Explanation:

VDC resource templates set the minimum and maximum limits for shared physical device resources when you create the VDC. The Cisco NX-OS software reserves the minimum limit for the resource to the VDC. Any resources allocated to the VDC beyond the minimum are based on the maximum limit and availability on the device. You can explicitly specify a VDC resource template, or you can use the default VDC template provided by the Cisco NX-OS software. VDC templates set limits on the following resources:

IPv4 multicast route memory IPv6 multicast route memory IPv4 unicast route memory IPv6 unicast route memory Port channels

Switch Port Analyzer (SPAN) sessions VLANs

Virtual routing and forwarding instances (VRFs)

Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx- os/virtual_device_context/configuration/guide/b-7k-Cisco-Nexus-7000-Series-NX-OS-Virtual- Device-Context-Configuration-Guide/vdc-res-template.html

Question No.58

Refer to the exhibit. Which statement based on these two outputs that were collected 24 hours apart is true?

image

  1. The Site 2 OTV edge device has gone down.

  2. The MAC address cannot be discovered on two separate port channel interfaces.

  3. The MAC address that ends in 020a moved to the local site 23 hours ago.

  4. The Overlay1 IP address should be a multicast IP address.

Correct Answer: C

Question No.59

Which two RFCs are supported by Cisco NX-OS devices for OSPFv2? (Choose two.)

  1. RFC 2238

  2. RFC 1918

  3. RFC 1583

  4. RFC 2453

  5. RFC 2740

Correct Answer: AC

Question No.60

Which three parameters can be set when configuring a Cisco MDS 9000 Series Switch to use a TACACS server? (Choose three.)

  1. group-size

  2. deadtime

  3. timeout

  4. keep-alive

  5. retransmit

Correct Answer: BCE

Get Full Version of the Exam
300-165 Dumps
300-165 VCE and PDF

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.