Achieve New Updated (September) Microsoft 70-410 Examination Questions 231-240

Ensurepass

 

QUESTION 231

You work as an administrator at ENSUREPASS.com. The ENSUREPASS.com network consists of a single domain named ENSUREPASS.com. All servers on the ENSUREPASS.com network have Windows Server 2012 R2 installed.

You have received instructions to convert a basic disk to a GPT disk.

Which of the following is TRUE with regards to GPT disks? (Choose all that apply.)

 

A.

To convert a basic disk to a GPT disk, the disk must not contain any partitions or volumes.

B.

You can convert a basic disk to a GPT disk, regardless of partitions or volumes.

C.

GPT is required for disks larger than 2 TB.

D.

GPT is required for disks smaller than 2 TB.

E.

The GPT partition style can be used on removable media.

F.

GPT disks make use of the standard BIOS partition table.

 

Correct Answer: AC

Explanation:

A. For a drive to be eligible for conversion to dynamic, all basic data partitions on the drive must be contiguous

C. GPT allows a much larger partition size greater than 2 terabytes (TB) D. 2 terabytes is the limit for MBR disks.

E. Dynamic disks are not supported on portable computers, removable disks, detachable disks that use USB or IEEE 1394 interfaces

F. Windows only supports booting from a GPT disk on systems that contain Unified Extensible Firmware Interface (UEFI) boot firmware.

Master boot record (MBR) disks use the standard BIOS partition table. GUID partition table (GPT) disks use unified extensible firmware interface (UEFI). One advantage of GPT disks is that you can have more than four partitions on each disk. GPT is also required for disks larger than 2 terabytes.

Portable computers and removable media. Dynamic disks are not supported on portable computers, removable disks, detachable disks that use Universal Serial Bus (USB) or IEEE 1394 (also called FireWire) interfaces, or on disks connected to shared SCSI buses. If you are using a portable computer and right-click a disk in the graphic
al or list view in Disk Management, you will not see the option to convert the disk to dynamic.

Dynamic disks are a separate form of volume management that allows volumes to have noncontiguous extents on one or more physical disks. Dynamic disks and volumes rely on the Logical Disk Manager (LDM) and Virtual Disk Service (VDS) and their associated features. These features enable you to perform tasks such as converting basic disks into dynamic disks, and creating fault-tolerant volumes. To encourage the use of dynamic disks, multi-partition volume support was removed from basic disks, and is now exclusively supported on dynamic disks. GPT disks can be converted to MBR disks only if all existing partitioning is first deleted, with associated loss of data.

Q. What happens when a basic disk is converted to dynamic?

A. For a drive to be eligible for conversion to dynamic, all basic data partitions on the drive must be contiguous. If other unrecognized partitions separate basic data partitions, the disk cannot be converted. This is one of the reasons that the MSR must be created before any basic data partitions. The first step in conversion is to separate a portion of the MSR to create the configuration database partition. All non-bootable basic partitions are then combined into a single data container partition. Boot partitions are retained as separate data container partitions. This is analogous to conversion of primary partitions.

Windows XP and later versions of the Windows operating system differs from Windows 2000 in that basic and extended partitions are preferentially converted to a single 0x42 partition, rather than being retained as multiple distinct 0x42 partitions as on Windows 2000.

http://technet.microsoft.com/en-us/library/cc725671.aspx

http://msdn.microsoft.com/en-us/library/windows/desktop/aa363785%28v=vs.85%29.aspx http://msdn.microsoft.com/en-us/library/windows/hardware/gg463525.aspx http://technet.microsoft.com/en-us/library/cc757696.aspx

http://technet.microsoft.com/en-us/library/cc776315.aspx

 

 

QUESTION 232

Server1 runs Windows Server 2012 R2 and is installed as an FTP server. Client use App1 to connect to Server1 for FTP. App1 use TCP port 21 for control and a dynamic port for data. You have allowed port 21 in firewall. What youshould next do to allow clients to use App1 to connect to server1 using ftp.

 

A
.

At Server1 allow firewall rule of outbound

B.

At Server1 allow firewall rule of inbound

C.

Netsh advfirewalldomainprofile state off

D.

Netsh advfirewall set global StatefulFtp enable

 

Correct Answer: D

Explanation:

Set global statefulftp

Configures how Windows Firewall with Advanced Security handles FTP traffic that uses an initial connection onone port to request a data connection on a different port. This affects both active and passive FTP.

 

clip_image001

 

http://technet.microsoft.com/en-us/library/cc771920%28v=ws.10%29.aspx http://support.microsoft.com/kb/832017/en-us#method20

 

 

QUESTION 233

You have a server named Server1 that runs Windows Server 2012 R2. You plan to enable Hyper-V Network Visualization on Server1. You need to install the Windows Network Virtualization Filter Driver on Server1. Which Windows PowerShell cmdlet should you run?

 

A.

Set-NetVirtualizationGlobal

B.

Set-NetAdapterVmq

C.

Add-WindowsFeature

D.

Enable-NetAdapterBinding

 

Correct Answer: D

 

 

QUESTION 234

A company has a forest with 4 sites. Subnets are as follows:

 

– MainOffice 172.16.1.0 Subnet: 255.255.255.0 Gateway 172.16.1.254

– Site1 192.168.12.0 Subnet: 255.255.255.0

– Site 2 192.168.13.0 Subnet: 255.255.255.0

– Site 3 192.168.14.0 Subnet: 255.255.255.0

– Site 4 192.168.15.0 Subnet: 255.255.255.0

 

You add a new server to the MainOffice and it needs to be able to communicate to all sites.

Which route command would you run?

 

A.

route add -p 192.168.8.0 netmask 255.255.252.0 172.16.1.254

B.

route add -p 192.168.0.0 netmask 255.255.248.0 172.16.1.254

C.

route add -p 192.168.12.0 netmask 255.255.252.0 172.16.1.254

D.

route add -p 192.168.12.0 netmask 255.255.240.0 172.16.1.254

 

Correct Answer: C

 

 

QUESTION 235

Server 1 and Server2 host a load-balanced Application pool named AppPool1. You need to ensure thatAppPool1 uses a group Managed Service Account as its identity. Which 3 actions should you perform?

 

A.

Install a domain controller that runs Windows Server 2012 R2, Run the New- ADServiceAccountcmdlet,

Modify the settings of AppPool1.

B.

Configure the Security settings of the contoso.com zone.

C.

Add a second legacy network adapter, and then run the Set-VMNetworkAdoptercmdlet.

D.

From Windows Powershell, run Get-DNSServerDiagnostics.

 

Correct Answer: A

Explanation:

For the application pool to use a group Managed Service account as its identity you will have to make sure that there is a domain controller where you can add the account and then modify the application pool accordingly. Thus you should use the New- ADServiceAccount on the domain controller that will create a new Active Directory service account.

 

 

QUESTION 236

Hotspot Question

You run a Windows Server 2012 R2and implementing 3 new printers in a warehouse. You need to makean exclusion forthese IP addresses within DHCP server. Select the location where would configure at the DHCP console?

 

clip_image002

 

Correct Answer:

 

clip_image003 

 

Explanation:

http://technet.microsoft.com/en-us/library/cc737978%28v=ws.10%29.aspx

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 237

Hotspot Question

You have a Server Core 2012 installation and all roles and features removed. The server does not haveaccess to Windows Update. You mount the network volume containing the installation files for Server 2012. You need to install DNS and DHCP server role. Which directory do you reference for installing?

 

 

clip_image004

 

Correct Answer:

 

clip_image005

Explanation:

http://blogs.technet.com/b/askpfeplat/archive/2013/02/24/how-to-reduce-the-size-of-the-winsxs-directory- and-free-up-disk-space-on-windows-server-2012-using-features-on-demand.aspx

 

 

QUESTION 238

Server1 runs Windows Server 2012 R2 and is installed as an FTP server. Client use App1 to connect to Server1 for FTP. App1 use TCP port 21 for control and a dynamic port for data. You have allowed port 21 in firewall. What youshould next do to allow clients to use App1 to connect to server1 using ftp.

 

A.

At Server1 allow firewall rule of outbound

B.

At Server1 allow firewall rule of inbound

C.

netshadvfirewalldomainprofile state off

D.

netshadvfirewall set global StatefulFtp enable

 

Correct Answer: D

Explanation:

Set global statefulftp Configures how Windows Firewall with Advanced Security handles FTP traffic that uses an initial connection onone port to request a data connection on a different port. This affects both active and passive FTP.

 

clip_image007

 

http://technet.microsoft.com/en-us/library/cc771920%28v=ws.10%29.aspx http://support.microsoft.com/kb/832017/en-us#method20

 

 

QUESTION 239

You run a Windows 2012 R2 Hyper-V Role Server, you need to shrink the size of files.vhd. Which powershellcmdlet option you should run first?

 

A.

Dismount-VHD

B.

Mount-VHD

C.

Resize-VHD

D.

Convert-VHD

&nb
sp;

Correct Answer: D

Explanation:

Correct Answer: Convert, as .vhd don’t support shrink. Convert-VHD – Converts the format, version type, and block size of a virtual hard disk file. Convert-VHD – Path c:testfiles.vhd – DestinationPath c:testtestvhdx.vhdx The Resize-VHD cmdlet resizes a virtual hard disk. This cmdlet lets you shrink or expand the size of a virtualhard disk, but the shrink operation is allowed only on VHDX virtual hard disks. The shrink operation fails ifit would shrink the virtual disk to less than its minimum size (available through the VHDX object’s MinimumSizeproperty). After converting a dynamically expanding VHD to the VHDX format, a new Shrink menu option becomesavailable in the Hyper-V UI as shown. VHDX format VHDs only expose the Shrink option when there is free space in the VHDX file to reclaim.

clip_image008

 

http://technet.microsoft.com/en-us/library/hh848454.aspx http://blogs.msdn.com/b/virtual_pc_guy/archive/2012/05/10/shrinking-a-vhd-in-windows- 8fast.aspx

http://technet.microsoft.com/en-us/library/hh848535.aspx

 

 

QUESTION 240

You only want to share a printer with Group1, administrators, central owner and operators. (pick 2 answers)

 

A.

Add permissions to Group1

B.

Remove permissions from administrators

C.

Add permissions to operators

D.

Add permissions to Central Owner

E.

Remove permissions from everyone.

 

Correct Answer: AE

Explanation:

 

clip_image009

Free VCE & PDF File for Microsoft 70-410 Real Exam

Instant Access to Free VCE Files: MCSE|MCSA|MCITP…
Instant Access to Free PDF Files: MCSE|MCSA|MCITP…